 |
|
 |
|
Hiinfo N1 series use the inserted hardware platform and inserted operating system, collecting touch screen technology, GPS navigation, security system, wireless network, mobile store, VOIP, immediate communication, onboard telephone, multimedia entertainment and visible reverse parking system together to make a wonderful onboard mobile multimedia entertainment platform.
|
 |
| |
 |
 |
| |
|
i. This machine is only used in the cathode earth 12V direct-current power supply system
This machine cannot be directly used in the 24V system automobile; it must install the power source inverter, or connect one of the two series batteries first. Otherwise, it may cause fire and damage.
ii. Don't disassemble or repack this machine
It will possibly cause electric shock, personal accident or fire. Please don't directly connect the power linesof other system and this machine. If there's any question to the safe installation of this machine, please inquire the Bluegrid dealer nearby.
iii. Do not install this machine in the place where hinder the operation of protection aerocyst or the steering wheel and the gearshift lever.
Or, it may cause accident or personal hurt.
iv. Only use the indicated fuse
Please use the same specific fuse (current standard) when change the fuse. Or else, it may cause fire.
|
 |
Cautions: |
Tips on power line (blue) |
a. Do not press the electric wire under the bolt or clamp in the mobile part (for example seat armrest).
b. Before connection, please turn the ignition key to OFF to avoid short-circuiting.
c. Only after all other leads being connected can the red and the black power input wire be connected. |
a. When this machine is connected to other three-dimensional acoustic parts, the nominal current of the connective automotive circuit must be bigger than the sum total of nominal current of each fuse.
b. When the nominal current of automotive circuit is not big enough, this machine can be directly connected to the battery. | | |
| Tip on safety |
| Please obey the traffic rules in your country. |
| |
 |
|
| The number in the list matches the number in the instruction |
| No. |
Descriptions |
Quantity |
Remarks |
(1)
|
Host computer
|
1
|
|
(2)
|
GPS receiver
|
1
|
|
(3)
|
Host computer mount 1
|
2
|
|
(4)
|
Host computer mount 2
|
2
|
|
(5)
|
Fixing screws
|
18
|
|
(6)
|
5M USB EXTW
|
2
|
|
(7)
|
5M VGA signal wire
|
1
|
|
(8)
|
150mm power line(12V input)
|
1 |
|
(9)
|
5M USBHUB supply lines
|
1 |
|
(10)
|
USB concentrator
|
1 |
|
| (11) |
High speed connector |
1 |
Choose and buy | |
| Accessory pictures |
 |
| |
| Please refer to the automotive system connection for details, and also must refer to all the other parts instructions in the system. |
| |
System |
 |
| |
|
Floor chart(example-concrete installation bases on the actual situation) |
 |
| |
 |
|
| Please refer to the "automotive system connection"(next page) for details. |
 |
Connection information |
| |
Connecting all the wires |
| Using high speed connector, and refer to the following chart or the connecting picture (page9). |
| Host computer |
Automobile |
Blue
|
Battery positive |
Black
|
Metal spot on the chassis or battery negative |
| Red |
PC power control line on M700AR or ACC power on the ignition switch(only when there's no power control switch) | |
| |
Using high speed connector |
 |
|
Cautions |
Connect the power input line after all the other wires be connected.
If the former ignition line is too thin, do not use the fast connector, but connect ACC power line to the former ignition line | | |
|
Automotive system connection |
| |
Please refer to other parts instructions in the system. Please refer to the "connection information".
Except the accessories with the machine,you must buy the parts listed here. When connecting such parts, please refer to its attached instruction. Please contact the supplier for the specification and other information of the parts needed to buy. |
| M700AR connection chart (click to see big picture) |
 |
| |
Avoid the accident caused by short-circuit
To avoid the accident caused by short-circuit, only when all the wires are connected,and the ignition key is on OFF connect the power line (blue and black), otherwise, accidental short-circuit may cause electric shock and serious damage.
When the fuse melts,
please check the circuit to find the reason before change it. When change it, please use the same specific fuse (current standard). It's dangerous to use different fuse or connect with wires, which may cause serious damage.
All the following leads should be connected, otherwise,may cause electric shock,device damage or fault.
Connect the blue lead to the battery positive.
Connect the black lead to the metal spot on the chassis |
|
Please obey the following tips. Otherwise,may cause electric shock¡¢device damage or fault. |
| |
Power line should be far from the signal line to avoid noise disturbance.
When disconnect the cable,you should hold the connector, do not pull the cable, or the cable may get loose. |
|
Installing the host computer |
| |
After all the connection finished,install the machine to the selected position. |
Before installation
The design of this machine is very safe,but wrong installation may cause accident. Confirm the following before installing.
Install on the firm surface,such as under the front seat or in the package. |
|
Cautions |
Don't install it nearby the combustibles or the place preventing radiating.
Don't install it in the hot place,such as close to the radiator, in the litter box of instrument desk or the heatproof place,because it will prevent this machine radiating.
Please prevent the outer pressure to avoid damaging the host computer.
Don't install the host computer in the following place:
The intense sunlight shines, the steam from the heater or other high temperature places;
The place which is unsafe or shivers fiercely;
Very moist, very dirty, or dusty places. | | |
Choose the installing position
a. Turn the ignition key to OFF or pull it out
b. Put the device into the planned installing position,check the length of cable and the installing conditions of the host computer |
| |
| Installation process |
| |
The first installation method |
 |
| |
| |
The second installation method |
 |
| |
| |
The way to connect (3)mount 1 and (4)mount 2 |
 |
 |
|
After installation and connection |
| |
Start automobile engine. Confirm that the brake light, the loudspeaker, and all electrical part are working.
Put through the switch line of host computer, the system can operate. |
 |
| |
Notice:
After installing the device, tighten all the loose electric wires. |
| |
| |
Fuse blown
Check whether the yellow and black lead ports connected right?
The power supply cannot be on
Check whether the yellow lead port has been connected or not?
Check whether the fuse has blown?
Noise disturbs tone quality
Check whether the power line and the signal line are separate routing?
If not, inspect whether uses the aluminum foil adhesive tape to wrap the signal wire? |
| |
| |
|
 |
|
|
|
| More |
|
